
In this article
- Start with the location and applicable design basis
- Wind speed and design pressure are not the same thing
- Building use and exposure answer different questions
- The building frame and its exterior components need different attention
- HVHZ and wind-borne debris requirements are different questions
- Can an old wind design be reused?
- Questions owners commonly ask
- What to provide with your request
Florida wind-load design involves more than selecting a wind speed for a city. The engineer needs to understand the location, building use, surrounding terrain and structure itself. Those inputs help establish the design basis for the members, surfaces and connections included in the project.
A wind-speed number copied from a nearby property or an online map is not a complete engineering design. Two projects in the same area can require different evaluations.
Start with the location and applicable design basis
Provide the project address and permitting jurisdiction, along with the type of work and available permit information. The applicable code and referenced standard need to be established for the assignment. The most recently published standard is not automatically the edition governing every permit.
The ASCE Hazard Tool provides location-based hazard information with selectable criteria. Its output is an input to professional design, not a substitute for selecting and applying the appropriate requirements.
The adopted code matters more than the newest publication date
The Florida Building Commission lists the 8th Edition (2023) effective December 31, 2023. Its ASCE 7-22 fact sheet confirms the Building volume’s reference to ASCE 7-22. Check the permit’s governing edition, supplements and applicable provisions rather than assuming an old project or a draft future code sets the requirements.
For a homeowner, the practical question is whether the plans and calculations state a consistent design basis. For a designer, it is also essential to keep ultimate and allowable-stress terminology and the relevant load combinations consistent. This guide does not provide a conversion shortcut for project use.
Wind speed and design pressure are not the same thing
Wind speed is normally expressed in miles per hour; design pressure is normally expressed in pounds per square foot (psf). The mapped design wind speed is selected using the applicable criteria, including location and risk category. Exposure influences calculated pressures; it should not be described as changing the mapped speed itself. Height, topography, geometry and internal-pressure assumptions can also affect the calculation.
This explains why two nearby projects with the same mapped speed can require different design pressures. It also explains why a product advertised for a particular “mph rating” is not enough information to establish suitability for a specific opening, roof zone or connection.
Building use and exposure answer different questions
The building’s use helps establish the relevant risk category. Exposure concerns the terrain and surroundings affecting wind approaching the structure. These concepts should not be used interchangeably.
An open waterfront setting and a developed inland setting may present different exposure considerations, even within the same community. Our guide to exposure category in building design explains why a view of the immediate yard is not enough to make that determination.
Geometry and openings influence the evaluation
The engineer needs information about building height, dimensions, roof configuration and openings. A roof addition, changed opening or attached structure may affect the work being evaluated. Send the current plans and identify changes since the original design.
For an existing building, available records should be considered alongside actual conditions. A drawing that predates an addition may not describe the present structure. When information is uncertain, clearly identify it instead of substituting a convenient assumption.
The building frame and its exterior components need different attention
The main wind-force-resisting system addresses the structure’s overall response. Components and cladding concern elements such as roof coverings, panels, windows and doors and their attachments. Local pressure effects can differ across surfaces, including roof edges and corners. A pressure used for one purpose should not be copied into a different check without justification.
A conceptual example is a roof project where a panel has a documented rating, but its attachment spacing and supporting substrate differ from the tested or approved assembly. The rating alone does not resolve that difference. The design professional must connect the product information to the project’s required pressures and installation conditions.
Roof appurtenances and rooftop equipment also influence the wind design and must be included in the evaluation, along with their attachments and supporting structure. Provide their locations and available equipment or product information so the engineer can account for them.
Connections are part of the design
Wind-related forces must be addressed through the relevant structural system, including its connections and supports. Specifying a member without considering how it attaches to the rest of the structure leaves an important question unanswered.
Similarly, a product approval or manufacturer’s detail must be evaluated for the intended application. It does not automatically resolve every site-specific condition, attachment or supporting-structure issue.
HVHZ and wind-borne debris requirements are different questions
Miami-Dade and Broward counties form Florida’s High-Velocity Hurricane Zone. That designation should not be used as another name for every coastal location. Wind-borne debris requirements also need to be evaluated under the applicable code; a site outside the HVHZ may still have opening-protection requirements.
Avoid choosing windows, shutters or roof products solely from a county-wide marketing label. The applicable approval, limitations, pressures and attachment details must fit the project. Product approval does not replace the need to evaluate the supporting structure.
Can an old wind design be reused?
An engineer must determine whether its assumptions, code basis and scope fit the current project. Reusing a number or detail without that review can overlook differences in the structure or site. No design should be described as hurricane-proof.
Florida Engineering offers structural design services throughout Florida. Share your plans and project information to define the engineering scope, deliverables and timing.
Questions owners commonly ask
What wind speed should I use in Florida?
Use the project-specific value established from the governing criteria. Statewide ranges are not a reliable substitute. Give the engineer the exact location and building use, not only the nearest city.
Is a wind-mitigation inspection the same as wind-load engineering?
No. An inspection documenting existing features for another purpose is not automatically a calculation package for proposed structural work. Identify the report or deliverable you actually need when requesting services.
Does stronger material automatically solve a wind issue?
No. The attachments and supporting construction must also be addressed. Increasing one member’s size does not demonstrate that the complete load path is adequate.
What to provide with your request
- Project address, intended use and permitting information.
- Current architectural and structural drawings, if available.
- Building dimensions, roof configuration and proposed modifications.
- Existing product information and connection details, including roof appurtenances and rooftop equipment.
- Photographs and records of prior alterations or damage.







